 
|
|
|
|
|
|
 |
Bradley Beach Consulting Mechanical Engineering and Design Services |
|
Pro/Engineer Model LibraryTo go back to the Pro/E page click this link Back to Pro/E page |
Thread forming screws for plastics |
This zip file contains a model with a family table of 4 different types of thread forming pan headed fasteners. Plastite 48, Plastite 45, Delta PT, and Type B Key parameters are TYPE, SCREW_SIZE, and LENGTH. The model also has a parameter called "HOLE SIZE" which is the nominal hole size needed in a plastic boss for that screw. There is also a little application information written into the family table for each screw type.(Pro/E 2000i) |
|
PEM Self Clinching Nut |
This zip file contains a model with a family table of PEM self clinching nuts for use in sheet metal applications. Same product is sold under other names such as Captive. (Pro/E 2000i2) |
|
PEM Self Clinching Threaded Stud  |
This zip file contains a model with a family table of PEM self clinching threaded stud for use in sheet metal applications. Same product is sold under other names such as Captive. (Pro/E 2000i2) |
|
PEM Self Clinching Standoffs  |
This zip file contains a model with a family table of PEM self clinching standoff for use in sheet metal applications. Same product is sold under other names such as Captive. (Pro/E 20001) |
|
PEM Self Clinching Flush Nut  |
This zip file contains a model with a family table of PEM self clinching Flush Fasteners for use in sheet metal applications. Same product is sold under other names such as Captive. (Pro/E 2000i2) |
|
Spur Gear Small Diameter  |
Use this model if the number of teeth is less than 43. This zip file contains a model of a spur gear I did as part of a project. I don't remember the reference I used for the equations of the involute tooth form, however it appears correct. There are three model parameters that can be modified, DP - diametral pitch, N - number of teeth, and PRESSANGLE - pressure angle. (Pro/E 2000i) |
|
| Spur Gear Large Diameter |
Use this model if the number of teeth exceeds 42. This zip file contains a model of a spur gear I did as part of a project. I don't remember the reference I used for the equations of the involute tooth form, however it appears correct. There are three model parameters that can be modified, DP - diametral pitch, N - number of teeth, and PRESSANGLE - pressure angle. (Pro/E 2001) |
|
Snap-in Nyliner Bearing  |
This zip file contains a model of a standard snap-in bearing (Nyliner- Thompson brand). They are economical bearings for use in sheet metal. Key parameters are SHAFT_SIZE AND PLATE_THICKNESS. Information about the housing bore is part of the family table. (Pro/E 2000i) |
|
Standard Flanged Nyliner Bearing (Types 5&6)  |
This zip file contains a model of a standard flanged bearing (Nyliner- Thompson brand Type 5&6). These bearing can have an anti-rotate key (type 6) or no anti-rotate key (type 5). Key parameters are SHAFT_SIZE, LENGTH, and ANTI_ROTATION_KEY. Information about the housing bore are part of the family table. (Pro/E 2000i) |
|
Parker series 2-XXX O-ring family table  |
This zip file contains a family table model of a the Parker series 2-XXX oring sizes. Key parameters are INNER_DIAMETER, WIDTH, and DASH_NUMBER. (Pro/E 2000i) |
|
Rotor Clip E Rings, External Retaining Rings |
This zip file contains a family table model of a Rotor Clip E Ring. Key parameters are SHAFT_DIAMETER and OD_INSTALLED (installed outside diameter). Also included as parameters are the groove diameter, width and depth (depth is a bit redundant, but there it is). (Pro/E 20001) |
|
Rotor Clip RE Rings, Reinforced External Retaining Rings |
This zip file contains a family table model of a Rotor Clip RE Ring (Reinforced E-Ring - permits higher thrust loading and increase rotational speed). Key parameters are SHAFT_DIAMETER and OD_INSTALLED (installed outside diameter). Also included as parameters are the groove diameter, width and depth (depth is a bit redundant, but there it is). (Pro/E 20001) |
|
Rotor Clip HO Rings, Internal Retaining Rings |
This zip file contains a family table model of a Rotor Clip HO Ring. Key parameter is HOUSING_DIA or HOUSING_DIA_FRACTION or HOUSING_DIA_METRIC_MM. Also included as parameters are the groove diameter, width and depth and free diameter. (Pro/E 2000i) |
|
Rotor Clip SH Rings, External Retaining Rings |
This zip file contains a family table model of a Rotor Clip HO Ring. Key parameter is SHAFT_DIA or SHAFT_DIA_FRACTION or SHAFT_DIA_METRIC_MM. Also included as parameters are the groove diameter, width and depth and free diameter. (Pro/E 2000i) |